2SP0115T

Dual-Channel SCALE-2 Plug-and-Play Driver for EconoDUAL IGBT Modules

SCALE-2 Technology

Electrical Interface

Embedded Paralleling Capability

Short Description

2SP0115T is the ultimate low-cost ultra-compact driver platform for EconoDUAL^TM IGBT modules. As a member of the CONCEPT plug-and-play driver family, it satisfies the requirements for optimized electrical performance and noise immunity.

The highly integrated SCALE-2 chipset reduces the component count by 80% compared to conventional solutions, thus significantly increasing reliability and reducing costs.

Thanks to SCALE-2 technology, the 2SP0115T family comprises complete and extremely compact two-channel IGBT drivers equipped with DC/DC converters, short-circuit protection, advanced active clamping and supply-voltage monitoring.

Users need only solder them onto the corresponding IGBT module. The system can then be put into immediate operation with no further development or matching effort. Shortest design cycles are achieved without compromising overall system efficiency in any way.

The embedded paralleling capability allows easy inverter design covering higher power ratings.

Specifically adapted drivers are available for all module types. The DIC20 electrical interface is very simple and easy to use.

Driving Parallel-Connected IGBTs

The driver allows direct parallel connection of any number of EconoDUAL modules with individual drivers. This new pioneering concept for simple and reliable parallel connection makes it practical for the first time to set up converter series with discrete modules as well as parallel-connected IGBTs without any additional development effort.

Direct parallel connection: How does it work?

Electrical Interface DIC20

The 2SP0115T driver series is equipped with DIC20 electrical interface, fully compatible to PrimePACK^TMdriver series 2SP0320T. The DIC20 electrical interface is very simple and easy to use.

The driver has the following terminals:

■ Power supply and GND terminals
■ 2 x drive signal inputs
■ 2 x status outputs (failure returns)
■ 1 x mode selection (half-bridge mode / direct mode)
■ 1 x input to set the blocking time

All inputs are ESD-protected and all digital inputs have Schmitt-trigger characteristics. For more details, check the product documentation.

Key Data Overview

Parameter	Min	Typical	Max	Unit
Nominal supply voltage		15		V
Supply current @ f_IN 0Hz		33		mA
Supply current, full load			220	mA
Output power per channel		1		W
Gate voltage		+15/-8		V
Peak output current (gate current)	-8		+15	A
Switching frequency f_{IN (Note 1)}	0		50	kHz
Duty cycle	0		100	%
Turn-on delay		75		ns
Turn-off delay		65		ns
Creepage distance primary-secondary	12.6			mm
Creepage secondary-secondary	6.6			mm
Clearance distance primary-secondary	12.3			mm
Clearance distance secondary-secondary	6.6			mm
Dielectric test voltage (600V/1200V versions)	3800			V_AC
Dielectric test voltage (1700V versions)	5000			V_AC
Partial discharge extinction voltage (600/1200V versions)	1200			V_peak
Partial discharge extinction voltage (1700V versions)	1700			V_peak
dv/dt immunity, input to output		50		kV/us
Operating temperature 2SP0115T2Ax-xx	-20		+85	°C
Operating temperature 2SP0115T2B0-xx (Note 2)	-40		+85	°C

Note 1: Maximum switching frequency depends on the IGBT gate charge. See data sheet for actual value of specific driver.

Note 2: 2SP0115T2B0-xx versions with extended temperature range of -40...+85 °C available on request.

Data Sheets

For data sheets click into tables, column "Driver type no."

2SP0115T Drivers for 600V IGBTs

IGBT I_C	IGBT type no.	Brand	Driver type no.
450A	FF450R06ME3	Infineon	2SP0115T2Ax-FF450R06ME3
600A	FF600R06ME3	Infineon	2SP0115T2Ax-FF600R06ME3
Any	Any	Any	2SP0115T2Ax-06 (Note 3)

2SP0115T Drivers for 1200V IGBTs

IGBT I_C	IGBT type no.	Brand	Driver type no.
150A	FF150R12ME3G	Infineon	2SP0115T2Ax-FF150R12ME3G
200A	CM200DX-24S	Mitsubishi	2SP0115T2Ax-CM200DX-24S
225A	2MBI225VN-120-50	Fuji	2SP0115T2Ax-2MBI225VN-120-50
225A	FF225R12ME4	Infineon	2SP0115T2Ax-FF225R12ME4
300A	2MBI300VN-120-50	Fuji	2SP0115T2Ax-2MBI300VN-120-50
300A	FF300R12ME3	Infineon	2SP0115T2Ax-FF300R12ME3
300A	FF300R12ME4	Infineon	2SP0115T2Ax-FF300R12ME4
450A	CM450DX-24S	Mitsubishi	2SP0115T2Ax-CM450DX-24S
450A	2MBI450VN-120-50	Fuji	2SP0115T2Ax-2MBI450VN-120-50
450A	FF450R12ME3	Infineon	2SP0115T2Ax-FF450R12ME3
450A	FF450R12ME4	Infineon	2SP0115T2Ax-FF450R12ME4
600A	2MBI600VN-120-50	Fuji	2SP0115T2Ax-2MBI600VN-120-50
600A	FF600R12ME4	Infineon	2SP0115T2Ax-FF600R12ME4
Any	Any	Any	2SP0115T2Ax-12 (Note 3)

2SP0115T Drivers for 1700V IGBTs

IGBT I_C	IGBT type no.	Brand	Driver type no.
225A	FF225R17ME4	Infineon	2SP0115T2Ax-FF225R17ME4
300A	FF300R17ME3	Infineon	2SP0115T2Ax-FF300R17ME3
300A	FF300R17ME4	Infineon	2SP0115T2Ax-FF300R17ME4
450A	2MBI450U4N-170-50	Fuji	2SP0115T2Ax-2MBI450U4N-170-50
450A	FF450R17ME3	Infineon	2SP0115T2Ax-FF450R17ME3
450A	FF450R17ME4	Infineon	2SP0115T2Ax-FF450R17ME4
Any	Any	Any	2SP0115T2Ax-17 (Note 3)

Note 3: In product versions 2SP0115T2Ax-12 and 2SP0115T2Ax-17, the turn-on and turn-off gate resistors of both channels are not assembled in order to provide maximum flexibility. They must be assembled by the user before start of operation. Please refer to the corresponding data sheet for recommended gate resistors. It will be updated with new adaptations regularly.